Difference between revisions of "Makerfire Armor 65 Lite"

From Makerfire
Jump to: navigation, search
(Created page with " == Specification == <br><br> Wheelbase 65mm<br> Flight controller: Silverware FC <br> Motor: 7×16mm 17600KV<br> Propeller: 4-Blade 31mm <br> VTX: 5.8G/40...")
(No difference)

Revision as of 23:17, 14 November 2018


Wheelbase 65mm
Flight controller: Silverware FC
Motor: 7×16mm 17600KV
Propeller: 4-Blade 31mm
VTX: 5.8G/40CH/25mW
Camera: 650TVL/120°
Battery: 300mAh /3.8V/1S/30C/Lipo
Flight time: 4Min15Second
Remote Distance: 75 Meters

How to Flash Firmware for Lite FC

The only method to restore the factory PID is reflashing the firmware for the moment.

About how to flash the firmware, please check on Silverware offical website or RCG.


The firmware for Makerfire WhoopLite FC board is available in the attached file.

If You want to compile the files by yourself, please download the files here:



// U D U - Next PID term
// U D D - Next PID Axis
// U D R - Increase value
// U D L - Descrease value


Silverware is a firmware for some micro quadcopters, especially the whoop FPV racing.
Silverware supports level mode and acro mode. Also it can change the the settings for custom builds, or to adapt to personal preferences.
By default, Silverware changes modes, tune PIDs, calibrate accelerometer or save settings by stick sequences(also called gestures).
For example, the Frsky QX7 radio transmitter switches the FC's mode between level and acro by moving the right stick as show below.
For all the gestures in Silverware, please go to basic user manual supporting freshdesk.

The 25mW/48CH AIO camera in Armor65 lite is characterized by wide dynamic,
high-definition, wide angle and no delay.The light and mini AIO camera
supports button and frequency choice as well as NTSC/PAL TV system.
The LED will show video transmiter frequency,8 LEDS indicates the signal
channel, 6LEDS indicates the frequencey,the specific frequency will base
on the video trasnmitter frequency chart.

Chematic diagram for referenced product:

Long Press can switch over the
NTSC/PAL TV system.
Short Press can switch over the
vertical inverted image.
Long Press can switch the frequency
of the Video transmitter.
Short Press can switch over the specific
signal channel of currecnt frequency.
Finish frequency operation to configure automatically frequency
point and groups. It also is equipped with non-volatile memory function.


== Armor65 Lite radio transmitter ==

The toys like JJRC H67, Eachine E011 etc use the Bayang protocol radio transmitters.

Jumper T8SG radio transmitter
MTX-9D multiprotocol module (Suitable for Frsky Tanaris QX7 X9D X9D Plus X12S, Flysky TH9X, Turnigy 9XR/9XR PRO)
Other 4in1 multiprotocol module that support the Bayang protocol.
If not sure whether your radio transmitter could support this FC board, please email us (Support@makerfire.com) for help.

For example, if you have a Frsky Tanaris QX7 / X9D radio transmitter and want to try this FC board,

just plug in a MTX90 multiprotocol module.

Remote control configuration

1)Bayang protocol remote control configuration

Power up the Armor65 Lite, the FC indicator LED flashes slowly for 6 times and then turnes into fast flash mode. The fast flash mode shows the beginning of the binding mode.

There is the "di" sound in the buzzer when turn on the radio transmitter and then turn into the binding mode automatically.
After finishing the binding, the FC indicator LED fashes solid,and the radio transmitter has the "di" sound.

After finishing the binding, turn off the radio transmitter, the FC indicator LED turns into slowly flash mode.

Turn on the radio transmitter before power up the Armor65 Lite, then the binding fails.
When Changing the new battery needs binding again.

2)Take Frsky X9D as an example

Install the MTX9D module in Frsky X9D radio transmitter in the correct place.

Turn on the radio transmitter,and create a radio transmitter mode.
In MODEL SETUP setting page,Set “Internal RF”to " OFF" and “External RF”to "PPM".


INPUTS Setting

MAXER Setting


Turn off the radio transmitter.
Power up the Armor65 lite RTF and wait for the binding mode.
When the The indicator LED flashes fast,turn on the radio transmitter and push the right-Throttle to top-right direction.
The indicator LED turning the fast flash into solid shows binding is successfully.

3)T8SG remote control

Power up the Armor65 Lite, the FC indicator LED flashes slowly for 6 times and then turn into fast flash mode. The fast flash mode shows the beginning of the binding mode.

Turn on the radio transmitter, short press "ENT" and go into "“Main menu", press " ENT", go into "Model menu",choose "“Model Setup”page.
By default,the photo show below for your reference.
Adjust the cursor into "PPM In",set the receiver to "Bayang" and choose " Re-Init”.
Press "ENT" and enter the binding mode.The indicator LED turning the fast flash into solid shows binding is successfully.

The T8SG enters the binding mode automatically if setting has been finished in advance.
There is the "did" sound at the starting and finishing binding mode.



Any questions,please contact us.
Find us on soci

Headline text

al media:

Charging instructions


1 . Charge the battery in time when low voltage.
2 . Turn the USB charger into 4.35v before charging.
3 . The solid red light shows the battery is in charging,light off shows in full charge.


Armor65 Lite RTF (Silverware Firmware)

Package included:
1× Armor65 Lite RTF
1× Radio Transmitter
1× 300mAh 1S 3.8V Battery
1× One-way 4.35V Charger
1× Propeller Tool
4× Propellers
2× Screws
1× Service Card