Difference between revisions of "Makerfire Armor 65 Lite"

From Makerfire
Jump to: navigation, search
(SILVERWARE)
 
(30 intermediate revisions by the same user not shown)
Line 2: Line 2:
 
== Specification ==
 
== Specification ==
 
<br>
 
<br>
Wheelbase  65mm<br>
+
Wheelbase: 65mm<br>
Flight controller: Silverware FC <br>
+
Flight controller: Tiny Lite Silverware FC<br>
Motor:      7×16mm 17600KV<br>
+
Remote: Tiny lite RC<br>
Propeller:    4-Blade 31mm <br>
+
Motor :  7×16mm 17600KV(65000rpm@3.7V)<br>
VTX:        5.8G/40CH/25mW<br>
+
Propeller: 4-Blade 31mm<br>
Camera:    650TVL/120°<br>
+
VTX 5.8G/40CH/25mW<br>
Battery:      300mAh /3.8V/1S/30C/Lipo<br>
+
Camera : 800TVL/120°<br>
Flight time: 4Min15Second<br>
+
Battery: 300mAh /3.8V/1S/30C/Li-HV<br>
Remote Distance: 75 Meters<br>
+
Flight time: 4min20second<br>
 +
Remote Distance: 100 meters<br>
 +
<br><br>
  
<br>
+
== Control Instructions(Mode2) ==
 +
[[File:F17caozuoshili1.jpg | 900px]]
 +
<br><br>
 +
[[File:F17caozuoshili.jpg| 900px]]
 +
<br><br>
  
== How to Flash Firmware for Lite FC ==
+
== RC Gestures Setting (Mode2) ==
 
<br>
 
<br>
The only method to restore the factory PID is reflashing the firmware for the moment.<br>
+
* Left - Left - Down: acro mode<br>
 +
* Right - Right - Down : level mode<br>
 
<br>
 
<br>
About how to flash the firmware, please check on Silverware offical website or RCG.<br>
+
[[File:abc1.jpg | 500px]]
<br>
+
<br><br>
''http://sirdomsen.diskstation.me/dokuwiki/doku.php?id=gallery''<br>
+
* Up - Down - Up: Cycle pid term to the next ( P - I - D )<br>
''https://www.rcgroups.com/forums/showthread.php?2876797-Boldclash-bwhoop-B-03-opensource-firmware''<br>
+
* Up - Down - Down: Cycle pid axis to be changed ( Roll/Pitch - Yaw )<br>
 
+
[[File:abc2.jpg | 500px]] 
 
<br><br>
 
<br><br>
 
+
* Up - Down - Left: Decrease the selected value<br>
The firmware for Makerfire WhoopLite FC board is available in the attached file.<br>
+
* Up - Down - Right: Increase the selected value<br>
 
+
[[File:abc3.jpg | 500px]]
If You want to compile the files by yourself, please download the files here:<br>
 
<br>
 
''https://github.com/silver13/BoldClash-BWHOOP-B-03''<br>
 
 
 
 
<br><br>
 
<br><br>
'''Mode2'''<br><br>
 
// U D U - Next PID term<br>
 
// U D D - Next PID Axis<br>
 
// U D R - Increase value<br>
 
// U D L - Descrease value<br>
 
  
<br><br>
+
* Down - Down - Down: Accelerometer calibration / Save pids if changed
 +
[[File:abc4.jpg | 500px]]
  
== SILVERWARE ==
 
<br>
 
  
Silverware is a firmware for some micro quadcopters, especially the whoop FPV racing.<br>
+
'''VTX Introduction:'''<br><br>
Silverware supports level mode and acro mode. Also it can change the the settings for custom builds, or to adapt to personal preferences. <br>
 
By default, Silverware changes modes, tune PIDs, calibrate accelerometer or save settings by stick sequences(also called gestures).<br>
 
For example, the Frsky QX7 radio transmitter switches the FC's mode between level and acro by moving the right stick as show below.<br>
 
For all the gestures in Silverware, please go to basic user manual supporting freshdesk.
 
<br><br>
 
  
The 25mW/48CH AIO camera in Armor65 lite is characterized by wide dynamic,<br>
+
The 25mW/40CH AIO camera in Armor65 lite is characterized by wide dynamic,<br>
 
high-definition, wide angle and no delay.The light and mini AIO camera<br>
 
high-definition, wide angle and no delay.The light and mini AIO camera<br>
 
supports button and frequency choice as well as NTSC/PAL TV system.<br>
 
supports button and frequency choice as well as NTSC/PAL TV system.<br>
Line 56: Line 48:
 
channel, 6LEDS indicates the frequencey,the specific frequency will base<br>
 
channel, 6LEDS indicates the frequencey,the specific frequency will base<br>
 
on the video trasnmitter frequency chart.<br>
 
on the video trasnmitter frequency chart.<br>
 +
 
<br><br>
 
<br><br>
'''Chematic diagram for referenced product:'''<br><br>
+
Long Press can switch over the NTSC/PAL TV system.<br>
Long Press can switch over the<br>
+
Short Press can switch over the vertical inverted image.<br>
NTSC/PAL TV system.<br>
+
Long Press can switch the frequency of the Video transmitter.<br>
Short Press can switch over the<br>
+
Short Press can switch over the specific signal channel of currecnt frequency.<br>
vertical inverted image.<br>
+
Finish frequency operation to configure automatically frequency point and groups. It also is equipped with non-volatile memory function.<br>
Long Press can switch the frequency<br>
 
of the Video transmitter.<br>
 
Short Press can switch over the specific<br>
 
signal channel of currecnt frequency.<br>
 
Finish frequency operation to configure automatically frequency<br>
 
point and groups. It also is equipped with non-volatile memory function.<br>
 
 
<br><br>
 
<br><br>
[[File:211211.png]]<br>
+
[[File:211211.png | 500px]]<br>
[[File:34444.png]]<br>
+
[[File:34444.png | 500px]]<br>
 
<br>
 
<br>
 
<br>
 
<br>
 +
  
 
== Armor65 Lite radio transmitter ==
 
== Armor65 Lite radio transmitter ==
 
  
 
The toys like JJRC H67, Eachine E011 etc use the Bayang protocol radio transmitters.<br>
 
The toys like JJRC H67, Eachine E011 etc use the Bayang protocol radio transmitters.<br>
Line 87: Line 74:
 
just plug in a MTX90 multiprotocol module.<br>
 
just plug in a MTX90 multiprotocol module.<br>
 
<br><br>
 
<br><br>
 +
  
 
== Remote control configuration ==
 
== Remote control configuration ==
Line 107: Line 95:
 
When Changing the new battery needs binding again.<br>
 
When Changing the new battery needs binding again.<br>
 
<br><br>
 
<br><br>
2)'''Take Frsky X9D as an example'''<br>
+
2)'''Take Frsky X9D as an example '''<br>
 
<br><br>
 
<br><br>
 
Step1<br>
 
Step1<br>
Install the MTX9D module in Frsky X9D radio transmitter in the correct place.
+
Install the [https://shop.makerfire.com/products/mtx9d-multiprotocol-tx-module-for-frsky-x9d-x9d-plus-x12s-flysky-th9x-9xr-pro-taranis-q-x7-transmitter  MTX9D module] in Frsky X9D radio transmitter in the correct place.
 
<br><br>
 
<br><br>
 +
 +
[[File:090091.jpg | 500px]]
 +
 
Step2<br>
 
Step2<br>
 
Turn on the radio transmitter,and create a radio transmitter mode.<br>
 
Turn on the radio transmitter,and create a radio transmitter mode.<br>
 
In MODEL SETUP setting page,Set “Internal RF”to " OFF" and “External RF”to "PPM".<br>
 
In MODEL SETUP setting page,Set “Internal RF”to " OFF" and “External RF”to "PPM".<br>
 +
 +
[[File:255885.jpg | 500px]]
 +
 
<br><br>
 
<br><br>
 
Step3<br><br>
 
Step3<br><br>
Line 122: Line 116:
 
Ele--->Thr<br>
 
Ele--->Thr<br>
 
Rud--->Rud<br>
 
Rud--->Rud<br>
 +
 +
[[File:Example3333.jpg | 500px]]
 
<br><br>
 
<br><br>
 
MAXER Setting<br>
 
MAXER Setting<br>
 
CH1-->Thr<br>
 
CH1-->Thr<br>
 
CH2-->Ail<br>
 
CH2-->Ail<br>
CH1-->Ele<br>
+
CH3-->Ele<br>
CH1-->Rud<br>
+
CH4-->Rud<br>
 +
 
 +
[[File:Exampledewew.jpg | 500px]]
 
<br><br>
 
<br><br>
 
Step4<br>
 
Step4<br>
Line 150: Line 148:
 
There is the "did" sound at the starting and finishing binding mode.<br>
 
There is the "did" sound at the starting and finishing binding mode.<br>
 
<br>
 
<br>
www.makerfire.com<br>
 
<br>
 
WIKI:http://wiki.makerfire.com/index.php/Main_Page
 
<br>
 
  
Any questions,please contact us.<br>
+
[[File:Exampleqqqq.png | 500px]]
Email:support@makerfire.com
+
 
<br>
+
<br><br>
Find us on social media:[https://www.facebook.com/pages/Makerfire/897527320310788 facebook]<br><br>
+
 
 +
4)'''Other radio transmitter'''<br>
 +
 
 +
CH1:AIL(ROLL)<br>
 +
CH2: ELE (PITCH)<br>
 +
CH3: THR (THROTTLE)<br>
 +
CH4:RUD (YAW)<br>
 +
CH5:ARM/DISARM(1000:DISARM,2000:ARM)<br>
 +
CH6:ANGLE/ACRO(1000:ANGLE,2000:ACRO)<br>
  
 +
<br><br>
  
 
== Charging instructions ==
 
== Charging instructions ==
<br><br>
+
<br>
 
Notes:<br><br>
 
Notes:<br><br>
 
1 . Charge the battery in time when low voltage.<br>
 
1 . Charge the battery in time when low voltage.<br>
Line 169: Line 172:
  
 
<br>
 
<br>
 +
 +
 +
  
 
== PACKAGE ==
 
== PACKAGE ==
Line 183: Line 189:
 
2× Screws<br>
 
2× Screws<br>
 
1× Service Card<br>
 
1× Service Card<br>
 +
3 x Sticker<br>
 +
<br><br>
 +
 +
 +
== How to Flash Firmware for Lite FC ==
 +
<br>
 +
The only method to restore the factory PID is reflashing the firmware for the moment.<br>
 +
<br>
 +
About how to flash the firmware, please check on Silverware offical website or RCG.<br>
 +
<br>
 +
 +
''https://www.rcgroups.com/forums/showthread.php?2876797-Boldclash-bwhoop-B-03-opensource-firmware''<br>
 +
 +
<br><br>
 +
 +
The firmware for Makerfire TinyLite FC board is available in the attached file.<br>
 +
 +
If You want to compile the files by yourself, please download the files here:<br>
 +
<br>
 +
 +
''https://github.com/NotFastEnuf/NFE_Silverware''<br>
 +
<br>
 +
''https://github.com/silver13/BoldClash-BWHOOP-B-03''<br>
 +
<br>
 +
Instructions:<br>
 +
<br>
 +
''http://edu.litebee.com/document/armor65.pdf''<br>
 +
 +
<br><br>
 +
 +
== NotFastEnuf/NFE_Silverware ==
 +
<br>
 +
Silverware is an open-source flight controller firmware developed by GitHub user silver13 for the H8 mini, BWhoop B03, and Eachine E011/E011C FCs. It was forked and further refined by GitHub user NotFastEnuf<br>
 +
<br>
 +
Silverware is a firmware for some micro quadcopters, especially the whoop FPV racing.<br>
 +
Silverware supports level mode and acro mode. Also it can change the the settings for custom builds, or to adapt to personal preferences. <br>
 +
By default, Silverware changes modes, tune PIDs, calibrate accelerometer or save settings by stick sequences(also called gestures).<br>
 +
For example, the Frsky QX7 radio transmitter switches the FC's mode between level and acro by moving the right stick as show below.<br>
 +
<br><br>
 +
== Instructions ==
 +
<br>
 +
http://www.makerfire.cn/Armor65Lite.pdf<br>
 +
<br><br>
 +
Any questions,please contact us.<br>
 +
Email:support@makerfire.com
 +
<br>
 +
Find us on social media:[https://www.facebook.com/pages/Makerfire/897527320310788 facebook]<br><br>

Latest revision as of 14:21, 23 July 2019

Specification


Wheelbase: 65mm
Flight controller: Tiny Lite Silverware FC
Remote: Tiny lite RC
Motor : 7×16mm 17600KV(65000rpm@3.7V)
Propeller: 4-Blade 31mm
VTX : 5.8G/40CH/25mW
Camera : 800TVL/120°
Battery: 300mAh /3.8V/1S/30C/Li-HV
Flight time: 4min20second
Remote Distance: 100 meters


Control Instructions(Mode2)

F17caozuoshili1.jpg

F17caozuoshili.jpg

RC Gestures Setting (Mode2)


  • Left - Left - Down: acro mode
  • Right - Right - Down : level mode


Abc1.jpg

  • Up - Down - Up: Cycle pid term to the next ( P - I - D )
  • Up - Down - Down: Cycle pid axis to be changed ( Roll/Pitch - Yaw )

Abc2.jpg

  • Up - Down - Left: Decrease the selected value
  • Up - Down - Right: Increase the selected value

Abc3.jpg

  • Down - Down - Down: Accelerometer calibration / Save pids if changed

Abc4.jpg


VTX Introduction:

The 25mW/40CH AIO camera in Armor65 lite is characterized by wide dynamic,
high-definition, wide angle and no delay.The light and mini AIO camera
supports button and frequency choice as well as NTSC/PAL TV system.
The LED will show video transmiter frequency,8 LEDS indicates the signal
channel, 6LEDS indicates the frequencey,the specific frequency will base
on the video trasnmitter frequency chart.



Long Press can switch over the NTSC/PAL TV system.
Short Press can switch over the vertical inverted image.
Long Press can switch the frequency of the Video transmitter.
Short Press can switch over the specific signal channel of currecnt frequency.
Finish frequency operation to configure automatically frequency point and groups. It also is equipped with non-volatile memory function.


211211.png
34444.png



Armor65 Lite radio transmitter

The toys like JJRC H67, Eachine E011 etc use the Bayang protocol radio transmitters.


Jumper T8SG radio transmitter
MTX-9D multiprotocol module (Suitable for Frsky Tanaris QX7 X9D X9D Plus X12S, Flysky TH9X, Turnigy 9XR/9XR PRO)
Other 4in1 multiprotocol module that support the Bayang protocol.
If not sure whether your radio transmitter could support this FC board, please email us (Support@makerfire.com) for help.

For example, if you have a Frsky Tanaris QX7 / X9D radio transmitter and want to try this FC board,
just plug in a MTX90 multiprotocol module.



Remote control configuration


1)Bayang protocol remote control configuration

Step1
Power up the Armor65 Lite, the FC indicator LED flashes slowly for 6 times and then turnes into fast flash mode. The fast flash mode shows the beginning of the binding mode.

Step2
There is the "di" sound in the buzzer when turn on the radio transmitter and then turn into the binding mode automatically.
After finishing the binding, the FC indicator LED fashes solid,and the radio transmitter has the "di" sound.

After finishing the binding, turn off the radio transmitter, the FC indicator LED turns into slowly flash mode.

Notes:
Turn on the radio transmitter before power up the Armor65 Lite, then the binding fails.
When Changing the new battery needs binding again.


2)Take Frsky X9D as an example


Step1
Install the MTX9D module in Frsky X9D radio transmitter in the correct place.

090091.jpg

Step2
Turn on the radio transmitter,and create a radio transmitter mode.
In MODEL SETUP setting page,Set “Internal RF”to " OFF" and “External RF”to "PPM".

255885.jpg



Step3

INPUTS Setting
Thr--->Ail
Ail---->Ele
Ele--->Thr
Rud--->Rud

Example3333.jpg

MAXER Setting
CH1-->Thr
CH2-->Ail
CH3-->Ele
CH4-->Rud

Exampledewew.jpg

Step4

Turn off the radio transmitter.
Power up the Armor65 lite RTF and wait for the binding mode.
When the The indicator LED flashes fast,turn on the radio transmitter and push the right-Throttle to top-right direction.
The indicator LED turning the fast flash into solid shows binding is successfully.



3)T8SG remote control

Power up the Armor65 Lite, the FC indicator LED flashes slowly for 6 times and then turn into fast flash mode. The fast flash mode shows the beginning of the binding mode.


Turn on the radio transmitter, short press "ENT" and go into "“Main menu", press " ENT", go into "Model menu",choose "“Model Setup”page.
By default,the photo show below for your reference.
Adjust the cursor into "PPM In",set the receiver to "Bayang" and choose " Re-Init”.
Press "ENT" and enter the binding mode.The indicator LED turning the fast flash into solid shows binding is successfully.

The T8SG enters the binding mode automatically if setting has been finished in advance.
There is the "did" sound at the starting and finishing binding mode.

Exampleqqqq.png



4)Other radio transmitter

CH1:AIL(ROLL)
CH2: ELE (PITCH)
CH3: THR (THROTTLE)
CH4:RUD (YAW)
CH5:ARM/DISARM(1000:DISARM,2000:ARM)
CH6:ANGLE/ACRO(1000:ANGLE,2000:ACRO)



Charging instructions


Notes:

1 . Charge the battery in time when low voltage.
2 . Turn the USB charger into 4.35v before charging.
3 . The solid red light shows the battery is in charging,light off shows in full charge.




PACKAGE


Armor65 Lite RTF (Silverware Firmware)

Package included:
1× Armor65 Lite RTF
1× Radio Transmitter
1× 300mAh 1S 3.8V Battery
1× One-way 4.35V Charger
1× Propeller Tool
4× Propellers
2× Screws
1× Service Card
3 x Sticker



How to Flash Firmware for Lite FC


The only method to restore the factory PID is reflashing the firmware for the moment.

About how to flash the firmware, please check on Silverware offical website or RCG.

https://www.rcgroups.com/forums/showthread.php?2876797-Boldclash-bwhoop-B-03-opensource-firmware



The firmware for Makerfire TinyLite FC board is available in the attached file.

If You want to compile the files by yourself, please download the files here:

https://github.com/NotFastEnuf/NFE_Silverware

https://github.com/silver13/BoldClash-BWHOOP-B-03

Instructions:

http://edu.litebee.com/document/armor65.pdf



NotFastEnuf/NFE_Silverware


Silverware is an open-source flight controller firmware developed by GitHub user silver13 for the H8 mini, BWhoop B03, and Eachine E011/E011C FCs. It was forked and further refined by GitHub user NotFastEnuf

Silverware is a firmware for some micro quadcopters, especially the whoop FPV racing.
Silverware supports level mode and acro mode. Also it can change the the settings for custom builds, or to adapt to personal preferences.
By default, Silverware changes modes, tune PIDs, calibrate accelerometer or save settings by stick sequences(also called gestures).
For example, the Frsky QX7 radio transmitter switches the FC's mode between level and acro by moving the right stick as show below.


Instructions


http://www.makerfire.cn/Armor65Lite.pdf


Any questions,please contact us.
Email:support@makerfire.com
Find us on social media:facebook